BQFLN - WATERPROOF BSMT BONE WHT

  • MSDS: BQFLN
  • Manufacturer: VALSPAR CORP
  • Product Name: WATERPROOF BSMT BONE WHT
  • National Stock Number: 8010-00B220083
Product Identification

Product ID:WATERPROOF BSMT BONE WHT
MSDS Date:03/07/1990
FSC:8010
NIIN:00B220083
MSDS Number: BQFLN

Responsible Party
VALSPAR CORP
1101 THIRD STREET SOUTH
MINNEAPOLIS, MN 55415
US

Emergency Phone: 800-228-5635

Info Phone: 612-332-7371

Cage: 13374

Contractor
VALSPAR CORPORATION
MINNEAPOLIS, MN 55415 US

Telephone: 800-228-5635

Cage: 06758

Ingredients

SILICA, CRYSTALLINE - TRIPOLI

CAS: 1317-95-9

RTECS: VV7336000

Fraction By Weight: 5%

OSHA PEL SEE TABLE Z3

ACGIH TLV: 0.1 MG/M3 RDUST;9293


TITANIUM DIOXIDE

CAS: 13463-67-7

RTECS: XR2275000

Fraction By Weight: 10 - 15%

OSHA PEL 15 MG/M3 TDUST

ACGIH TLV: 10 MG/M3 TDUST; 9293


WATER

CAS: 7732-18-5

RTECS: ZC0110000

Fraction By Weight: 55 - 60%


WOLLASTONITE

CAS: 13983-17-0

Fraction By Weight: 10%


VINYL ACRYLIC COPOLYMER

CAS: 25067-01-0

Fraction By Weight: 15%

Hazards

Routes of Entry: Inhalation:YES Skin:YES Ingestion:YES
Reports of Carcinogenicity:NTP:NO IARC:NO OSHA:NO
Health Hazards Acute and Chronic:ACUTE: EYE, SKIN IRRITATION MAY OCCUR
WITH OVEREXPOSURE. CONTINUED BREATHING OF VAPORS MAY IRRITATE
RESPIRATORY TRACT CAUSING HEADACHE, NAUSEA AND DIZZINESS.
Explanation of Carcinogenicity:NONE OF THE COMPOUNDS IN THIS PRODUCT IS
LISTED BY IARC, NTP, OR OSHA AS A SUSPECTED OR KNOWN CARCINOGEN.
Effects of Overexposure:EYE, SKIN AND LUNG IRRITATION. CONTINUED
BREATHING OF VAPORS MAY IRRITATE RESPIRATORY TRACT CAUSING
HEADACHE, NAUSEA AND DIZZINESS. THIS PRODUCT MAY BE FATAL FROM
SWALLOWING LARGE AMOUNTS. MAY CAUSE N AUSEA, VOMITING, HEADACHES,
DIZZINESS, STUPOR, AND KIDNEY DAMAGE.
Medical Cond Aggravated by Exposure:ANY RESPIRATORY OR SKIN CONDITION.

First Aid

First Aid:INHALATION:REMOVE TO FRESH AIR. EYES: IMMEDIATELY FLUSH WITH
PLENTY OF WATER FOR 15 MINUTES HOLDING EYELIDS OPEN. GET MEDICAL
ATTENTION. SKIN: WASH WITH SOAP AND WATER. IF IRRITATION PERSISTS,
GET MED ICAL ADVICE. INGESTION:INDUCE VOMITING.GIVE 1 OR 2 GLASSES
OF WATER IF CONSCIOUS. GET IMMEDIATE MEDICAL HELP.

Fire Fighting

Flash Point Method:TCC
Flash Point:205F,96C
Lower Limits:NA
Upper Limits:NA
Extinguishing Media:USE WATER FOG, CARBON DIOXIDE, FOAM, OR DRY
CHEMICAL.
Fire Fighting Procedures:WEAR FIRE FIGHTING PROTECTIVE EQUIPMENT AND A
FULL FACED SELF CONTAINED BREATHING APPARATUS. COOL FIRE EXPOSED
CONTAINERS WITH WATER SPRAY.
Unusual Fire/Explosion Hazard:COMBUSTION OR HEAT OF FIRE MAY PRODUCE
HAZARDOUS DECOMPOSITION PRODUCTS AND VAPORS.

Accidental Release

Spill Release Procedures:WEAR APPROPRIATE PERSONAL PROTECTION
EQUIPMENT. CONTAIN SPILL WITH INERT ABSORBENT MATERIAL AND PUT INTO
VAPOR TIGHT CONTAINERS. PREVENT MATERIAL FROM CONTACTING ANY WATER
SOURCES OR STORM SEWERS.
Neutralizing Agent:NOT APPLICABLE.

Handling

Handling and Storage Precautions:STORE IN COMPLIANCE WITH GOOD
HOUSEKEEPING PROCEDURES. PROTECT FROM FREEZING, STORE AT
TEMPERATURES ABOVE 45 F. PROTECT FROM PHYSICAL DAMAGE.
Other Precautions:DO NOT TAKE INTERNALLY. DO NOT BREATHE MIST. AVOID
PROLONGED OR REPEATED BREATHING OF VAPOR. AVOID CONTACT WITH EYES.
USE WITH ADEQUATE VENTILATION. WASH THOROUGHLY AFTER HANDLING. READ
MANUFACTURER'S SAFETY PRECAUTIONS BEFORE USE.

Exposure Controls

Respiratory Protection:USE NIOSH/MSHA APPROVED RESPIRATORS TO REMOVE
SOLID AIRBORNE PARTICLES OF OVER SPRAY DURING SPRAY APPLICATIONS.
IN RESTRICTED VENTILATION AREAS USE NIOSH/MSHA APPROVED RESPIRATOR
DESIGNED TO REMOVE BO TH PARTICLES AND VAPOR.
Ventilation:SUFFICIENT VENTILATION IN VOLUME AND PATTERN SHOULD BE
PROVIDED TO KEEP AIR CONTAMINATION BELOW OSHA'S CURRENT PELS.
Protective Gloves:IMPERVIOUS NATURAL RUBBER GLOVES.
Eye Protection:SAFETY GOGGLES WITH OPTIONAL FACE SHIELD
Other Protective Equipment:PREVENT PROLONGED SKIN CONTACT BY USING
CLEAN WORK CLOTHING, INCLUDING A HAT.
Work Hygienic Practices:WASH HANDS BEFORE EATING, SMOKING OR USING
WASHROOM FACILITIES. DO NOT WEAR CONTAMINATED CLOTHING OR FOOTWEAR.
Supplemental Safety and Health
DO NOT HANDLE UNTIL MANUFACTURES SAFETY PRECAUTIONS HAVE BEEN READ AND
UNDERSTOOD. PROVIDE ADEQUATE VENTILATION OR RESPIRATORY PROTECTION
TO REMOVE DECOMPOSITION PRODUCTS DURING WELDING OR FLAME CUTTI NG
COATED SURFACES. DO NOT STORE OR USENEAR HEAT, SPARKS, OR FLAMES.

Chemical Properties

HCC:N1
Boiling Pt:B.P. Text:212F,100C
Vapor Pres:24.0
Vapor Density:.6
Spec Gravity:1.21
Solubility in Water:APPRECIABLE
Appearance and Odor:NORMAL FOR A COATINGS PRODUCT.
Percent Volatiles by Volume:68.35

Stability

Stability Indicator/Materials to Avoid:YES
WATER-REACTIVE MATERIALS
Stability Condition to Avoid:NONE
Hazardous Decomposition Products:MAY PRODUCE HAZARDOUS FUMES, INCLUDING
CARBON DIOXIDE AND CARBON MONOXIDE, WHEN HEATED.

Disposal

Waste Disposal Methods:DISPOSAL SHOULD BE MADE IN ACCORDANCE WITH ALL
APPLICABLE FEDERAL, STATE AND LOCAL LAWS AND REGULATIONS. DO NOT
INCINERATE CLOSED CONTAINERS.

Disclaimer (provided with this information by the compiling agencies):
This information is formulated for use by elements of the Department
of Defense. The United States of America in no manner whatsoever,
expressly or implied, warrants this information to be accurate and
disclaims all liability for its use. Any person utilizing this
document should seek competent professional advice to verify and
assume responsibility for the suitability of this information to their
particular situation.